Search results

It's a rainy weekend, so just doing some cleaning at my shop. I'll pull her out and snap some pics. *Knock on wood* I'll finally get back to it later this spring / summer. Looking forward to it. Sent from my XT1254 using Tapatalk

Been in storage a long time. Just cracked it open to grab some items. Stayed relatively clean at least... Sent from my XT1254 using Tapatalk

INB4 Geriatric jokes Yes it's a 2500 now. I was happy to scavenge parts off my 1500 to flesh it out though.

:doge: I'm alive! I'll post some fresh pics after I finish moving this month!

Yes! I'm in the process of moving right now (either renting or selling my old space) I've got all the gauge work done and the pillar, although it's not a perfect fit. I've got some finishing to do to it. I've driven the truck less than 15 miles in 2015? I'd have to doublecheck that number...

Interesting~ Good luck mon. Congratz!

Well I did set up the switches on independent add-a-circuits for power, and they get juice when the key is turned. I can just leave the one near my dimmer on all the time.. but I do like the ability to kill all the aftermarket stuff with a switch. I am getting closer to executing the rest of my...

Oh, you mean non-switched and have them turn on with accy? I have a few different colors for loom, just picked red. I will probably switch to black when I do the engine upgrades, as the components will be painted or powder coated.

Where are you going to stick it? (the CTS2)

Engine stuff will come, just getting the cab squared away. All the gauges have manual dimmers, and auto-dimming for when the headlights come on. I can tweak all of it later. I don't mind the pods so much, but I'll keep my eye out for something a little more stealthy. Keep in mind I don't...

Slow coolant leak on back-drivers side.. gotta track that down ;)

Yep, lol. I still need to remove and adjust the leads but getting there. Sent from my iPad using Tapatalk

Quick Update I've finished all of the wiring in engine compartment along with a clean DSP5 install. I've almost got all of the cab wiring complete with the new LED toggle switches. I've installed 2 near the radio that run my fog lights & accessories and 1 near my dimmer that runs all the new...

Got my wiring loom and shrink tubes for soldering wires. Not perfect, but it keeps it tidy until I tear it apart again. Splicing and prepping common wiring I got everything through the firewall. Wiring up the ECM tomorrow and finishing engine bay work. Moving into the cab and...

Progress. Got a little time to work on it tonight. This 1/4 - 1/8 NPT brass fitting will do for now. I plan on upgrading my intercooling piping soon anyway. I'll run an 1/8" tubing to the sending unit for the boost gauge. I stuffed a rag in above the hole I drilled. (just make sure you can...

Started raining, so I had to back it into the garage. I did clean up the gauge wiring a bit and started looking into getting everything connected. I decided to pipe all the cabling through the grommet for the accelerator. I'll take a shot when that's complete. No brackets on the gauges, just a...

Took out the front fender wells, and I need to order new plastic rivets.. mine are looking pretty beat up. Large harness passing through firewall. I plan on either using this for my wiring or find another way through. (Foglights, EGT, BOOST, CTS2 & DSP5) I would like to keep them all...

Parts and Progress New switches bitches Removed old fog light wiring + switches - to be replaced AutoCal arrived today so I can download my existing tunes and send to ATP Trucks / Idaho Rob After I get my sticker in July, i may use this excess 4 inch stainless for a muffler delete...

I'll be sure to pass that along, lol :turborofl: Ordered Got a few of these and a new relay for my fog lights on order. 22mm Angel Eye LED switches (2 stage)

I think I am going to scrap the lightbar plans and try to stick with subtle custom changes. I'm not knocking trucks that have them or their sense of style.. but I am starting to think it's not a good fit for this particular ride. Update : made it through the instructions on the cts2. Waiting...